[Vente] PCB carte Riser pour PC XT

Petites annonces "oldies only" sinon c'est dans le "Passage" que ça se passe
(Attention: concerne uniquement le matériel de collection).

Modérateurs : Papy.G, fneck, Carl

Falkayn
Messages : 715
Inscription : 12 juin 2018 18:18
Localisation : Montpellier

Re: [Vente] PCB carte Riser pour PC XT

Message par Falkayn »

pas de problème pour 2 pcb ,

J'ai 2 connecteurs isa si ca t'interesse. Et egalement les condos.

Suite en mp ?
Recherche : National JR-800 - Husky fc486 - TO16
Echange : Mac Plus&Classic - Sharp ...
Avatar de l’utilisateur
Arkhaan
Messages : 186
Inscription : 01 janv. 2022 10:04
Localisation : IDF

Re: [Vente] PCB carte Riser pour PC XT

Message par Arkhaan »

Je ne sais pas trop où centraliser les infos, donc je les pose là pour l'instant.

Configuration du PC XT :
  • PC Olivetti Prodest PC1 avec 1 x lecteur 3,5
  • Riser 2 x ISA (kit de Falkayn)

Cartes ISA testées avec succès :
  • XT-IDE assemblée par Falkayn
  • ACUMoS AVGA1 256Ko ISA 8/16bits, fonctionne sans problème et sans rien faire côté PC1

Cartes ISA testées sans succès :
  • Oak OTI067 512Ko ISA 8/16bits, affichage très délavée presque illisible le texte se confond avec le fond l'écran
  • Oak OTI037C 256Ko ISA 8/16bits, affichage très délavée presque illisible le texte se confond avec le fond l'écran
  • Paradise PVGA1A 256Ko ISA 8/16bits, ne démarre pas sur Olivetti PC1 - fonctionne bien sur IBM 5155

Les deux cartes Oak fonctionnent très bien sur un autre PC XT en remplacement d'une carte CGA.
Probablement un conflit avec la carte embarquée sur l'Olivetti.
Dernière modification par Arkhaan le 29 mars 2022 10:21, modifié 2 fois.
Falkayn
Messages : 715
Inscription : 12 juin 2018 18:18
Localisation : Montpellier

Re: [Vente] PCB carte Riser pour PC XT

Message par Falkayn »

si les cartes sont très consommatrices.

Peut être que la petite modification recommandé par l'auteur de la riser fonctionnera.
It has been brought to my attention that I forgot to enlarge the tracks for B5, B7 and B9 (-5V, -12V and +12V) and that they are not thick enough to carry currents in excess of 100mA without starting to heat up. This can be a problem when connecting ISA cards that draw high current from those lines.

However we also need to remember that the PC1 does not provide power on B5 and B7 (-5V and -12V respectively) so this is only a problem if you use a card that requires +12V from B9 and internally regulates it to whatever voltages it needs. If you really need to draw a lot of current from B9 (+12V) you can solder a small wire from the pad to the pin of the socket as a last resort solution.
Recherche : National JR-800 - Husky fc486 - TO16
Echange : Mac Plus&Classic - Sharp ...
Avatar de l’utilisateur
Arkhaan
Messages : 186
Inscription : 01 janv. 2022 10:04
Localisation : IDF

Re: [Vente] PCB carte Riser pour PC XT

Message par Arkhaan »

C est un bon point sous condition que la carte utilise du 12v.
De mon côté les cartes ISA VGA que j ai sous la main sont soit dépourvues de la broche B9 soit elle est présente mais non câblée.
darkmiky
Messages : 44
Inscription : 23 août 2016 18:26

Re: [Vente] PCB carte Riser pour PC XT

Message par darkmiky »

Bonjour, à tout hasard, vous resterait il un pcb?
Cordialement
Mike
Falkayn
Messages : 715
Inscription : 12 juin 2018 18:18
Localisation : Montpellier

Re: [Vente] PCB carte Riser pour PC XT

Message par Falkayn »

Je vais regarder si j'en ai encore.

Edit : Il reste un PCB, je te le reserve aux conditions de la premiere page : 5 euro port inclus pour la France.
Recherche : National JR-800 - Husky fc486 - TO16
Echange : Mac Plus&Classic - Sharp ...
Répondre