[ECH/VDS] le coin de DataPro
Modérateurs : Papy.G, fneck, Carl
Re: [ECH/VDS] le coin de DataPro
Donne (aux membres habitués du forum) ou échange imprimante EXL80 sans boîte, ruban sec... photo et test sur demande.
Recherche: cartouches Mattel Intellivision Imagic (loose)
Star Jacker et Lode Runner sur Yeno/SEGA SC-3000
Star Jacker et Lode Runner sur Yeno/SEGA SC-3000
Re: [ECH/VDS] le coin de DataPro
Bon l'imprimante est partie pour Elesias.
Il me reste des interfaces VG5200.
Il me reste des interfaces VG5200.
Recherche: cartouches Mattel Intellivision Imagic (loose)
Star Jacker et Lode Runner sur Yeno/SEGA SC-3000
Star Jacker et Lode Runner sur Yeno/SEGA SC-3000
- irios
- Messages : 3396
- Inscription : 04 nov. 2007 19:47
- Localisation : Rochefort du Gard (30)
- Contact :
Re: [ECH/VDS] le coin de DataPro
Pour quel type de Vtech laser recherches-tu un câble RVB ? Intéressé par une interface VG5200 !!!
http://irioslabs.over-blog.com/
La connaissance ne vaut que si elle est partagée par tout le monde.
I2C
La connaissance ne vaut que si elle est partagée par tout le monde.
I2C
Re: [ECH/VDS] le coin de DataPro
C'est pour le Laser 310... cependant il me semble que ce n'est pas possible, il semblerai que le signal ne soit pas RVB dans la machine... de toute façon mon LASER310 est en panne... il a fumé et je n'arrive pas à le démonter (j"ai pas de pompe à dessouder pour oter le blindage)
Recherche: cartouches Mattel Intellivision Imagic (loose)
Star Jacker et Lode Runner sur Yeno/SEGA SC-3000
Star Jacker et Lode Runner sur Yeno/SEGA SC-3000
Re: [ECH/VDS] le coin de DataPro
Et bien je prendrai bien un câble RVB pour mon Panasonic FS-A1F
brochage : http://www.msxvillage.fr/forum/topic.php?id=296
ou
brochage : http://www.msxvillage.fr/forum/topic.php?id=296
ou
It's for the Sony HB-F700, but it supposed to work for the Turbo-R and the Sanyo Wavy MSX2+ too.
SONY HB700 RGB plug: (seen from cable side)
-7------ 6
3----8---1
-5-------4
------2
SCART connector: (seen from cable side)
+------------------------------------+
\ 20 18 16 14 12 10 8 6 4 2 |
\ |
| 19 17 15 13 11 9 7 5 3 1 |
+----------------------------------+
How to connect:
DIN: Description: SCART:
1 audio ground 4 (and 5, 9, 13, 14, 18 to be sure)
2 audio right 2 (and 6 (mono))
3 status CVBS 8
4 CVBS 20
5 status RGB 16
6 red 15
7 green 11
8 blue 7
The signal on pin 3 (status RGB) functions like a switch signal, where any voltage from +3 to +12 volt signals 'on', and anything below that indicates 'off'. This is for instance used if you're connecting your computer to a TV with SCART input. In that case, the TV will automaticly switch to display of the RGB (SCART) signal when the computer is turned on.
It is usually connected to +12V (sometimes only some 5V, but this should work the same) through some series resistor.
The Sony F700 and Sanyo Wavy only put a composite sync signal (no complete video, only synchronisation signals) on pin 4, where the Turbo-R seems to put a complete composite video signal on this pin. An RGB monitor only uses this to extract the synchronisation signals, and therefore either composite sync, or composite video will do.
The signal on pin 5 (Ys, or luminance) is not really a signal, but carries a constant voltage of some 3 to 4 volts. Some monitors seem to need this though.
Recherche: cartouches Mattel Intellivision Imagic (loose)
Star Jacker et Lode Runner sur Yeno/SEGA SC-3000
Star Jacker et Lode Runner sur Yeno/SEGA SC-3000
Re: [ECH/VDS] le coin de DataPro
Y'a t'il des intéressés ?
Recherche: cartouches Mattel Intellivision Imagic (loose)
Star Jacker et Lode Runner sur Yeno/SEGA SC-3000
Star Jacker et Lode Runner sur Yeno/SEGA SC-3000
- fneck
- Site Admin
- Messages : 17426
- Inscription : 01 avr. 2007 12:03
- Localisation : Drôme Provençale (26)
- Contact :
Re: [ECH/VDS] le coin de DataPro
Par quoi ?
Fabien https://www.system-cfg.com
Les bonnes pratiques de l'utilisateur du forum viewtopic.php?f=14&t=3
Les bonnes pratiques de l'utilisateur du forum viewtopic.php?f=14&t=3